Merge branch 'v1.0.0' into develop

README.rst

@@ -53,6 +53,7 @@ Mopidy-Touchscreen to your Mopidy configuration file::
     enabled = true
     screen_width = 320
     screen_height = 240
+    resolution_factor = 8
     cursor = True
     fullscreen = False
     cache_dir = $XDG_CACHE_DIR/mopidy/touchscreen
@@ -67,6 +68,8 @@ The following configuration values are available:
 
 - ``touchscreen/screen_height``: The width of the resolution you want to use in
   pixels.
+  
+- ``touchscreen/resolutin_factor``: This value sets how big content is shown. Smaller values will make content bigger and less content will be displayed at once.
 
 - ``touchscreen/cursor``: If the mouse cursor should be shown. (If you use a
   touchscreen it should be false)
@@ -84,13 +87,27 @@ How to Setup
 
 Use the basic configuration to setup as most standard screens works fine without further configuration.
 
-Raspberry Pi and LCD Shields
-----------------------------
+Raspberry Pi
+------------
 
-If you are using a LCD Shield in Raspberry Pi you need to config your LCD and run mopidy with root privileges:
+If you are using this on a raspberry pi you have to run mopidy with root privileges:
+
+Run Mopidy with root privileges
+```````````````````````````````
+
+You can use ``sudo mopidy``.
+
+In case you are using musicbox edit ``/etc/init.d/mopidy`` file. Change ``DAEMON_USER=mopidy`` to ``DAEMON_USER=root``
+
+Do not forget that this is a workaround and that mopidy will run with root privileges.
+
+LCD Shields
+```````````
+
+If you are using a LCD Shield in Raspberry Pi you need to config your LCD:
 
 Configure your LCD Shield
-`````````````````````````
+'''''''''''''''''''''''''
 
 Add to the config the next variables::
 
@@ -105,16 +122,41 @@ To find your values find an example of using pygame with your LCD Shield and it
     os.environ["SDL_FBDEV"] = "/dev/fb1"
     os.environ["SDL_MOUSEDRV"] = "TSLIB"
     os.environ["SDL_MOUSEDEV"] = "event0"
+    
+GPIO Buttons
+````````````
 
-Run Mopidy with root privileges
-```````````````````````````````
+You can use GPIO buttons to controll mopidy touchscreen. To do that set the configuration::
 
-You can use ``sudo mopidy``.
+    [touchscreen]
+    gpio = True
+    gpio_left = 4
+    gpio_right = 27
+    gpio_up = 22
+    gpio_down = 23
+    gpio_enter = 24
 
-In case you are using musicbox edit ``/etc/init.d/mopidy`` file. Change ``DAEMON_USER=mopidy`` to ``DAEMON_USER=root``
+You can choose what pins to use:
 
-Do not forget that this is a workaround and that mopidy will run with root privileges.
+- ``touchscreen/gpio``: If you want to use gpio buttons. If this is set to false other gpio configuration values will be ignored.
+- ``touchscreen/gpio_left``: Pin used to simulate left key press.
+- ``touchscreen/gpio_right``: Pin used to simulate right key press.
+- ``touchscreen/gpio_up``: Pin used to simulate up key press.
+- ``touchscreen/gpio_down``: Pin used to simulate down key press.
+- ``touchscreen/gpio_enter``: Pin used to simulate enter key press.
+    
+All pins numbers are in BCM mode. You can check `here <http://raspberrypi.stackexchange.com/a/12967>`_ to see the numbers for your board.
+
+The buttons must be connected to GROUND.
+
+Pin - Button - Ground
+
+How To Use
+==========
 
+You can use it with a touchscreen or mouse clicking on the icons. 
+In case you are using a keyboard use arrow keys to navigate and enter to select.
+The GPIO buttons simulate keyboard keys so the use is exactly the same as using a keyboard.
 
 Help
 ====
@@ -165,7 +207,7 @@ Project resources
 Changelog
 =========
 
-v1.0.0 (UNRELEASED)
+v1.0.0 (2015-05-26)
 -------------------
 
 - Require Mopidy v1.0